Tuesday, April 17, 2007

Point - Counterpoint

Yesterday, a horrendous attack was carried out by a lone, crazed individual at Virgina Tech. 33 people (including the mass murderer) are dead, with dozens more wounded.

Though reports are conflicting, it seems the murderer did this with one hand gun, and a few spare magazines. No "assault" weapons were involved, and there were no "super high capacity" magazines... just the standard capacity magazines for the gun. Even if he were limited to 10 round magazines for the gun, he'd only need one, or at most two more, at $30 a piece, to achieve the same result.

No "assault weapons ban" would have stopped this mass murder.

He apparently purchased his gun legally, several months before.

No background check or waiting period would have stopped this mass murder.


It was initially thought that the murderer was a chinese national, who had acquired his guns illegally. This was plausible, because it is easier to buy a gnu illegally in many areas, than it is legally.

No ban on handguns, or even all guns, would have stopped this mass murder.


The murderer apparently took his time, sought out specifics locations, and blended in with the hysterical crowds when he wasn't actively shooting. He waited three hours while the police and security searched for him; and when the students started moving again, he started shooting again.

No Police presence short of an armed and trained officer in every room, and at every intersection would have stopped this mass murder


Dozens of police spread out throughout the campus couldn't find him, and couldn't stop him when he got up and started shooting again. The police COULD NOT STOP HIM.

One prospective "victim"; a student, a teacher, an administrator; armed with a gun; could have stopped this mass murder.


Why could one student do it when the police couldn't? Because the students were there all the time. They were there when the murderer stood up, took out his gun, and started shooting at the, disarmed by law and university policy, victims.

In Virginia, about 150,000 people have CCW permits; and though there are no accurate statistics, it is estimated that out of a population of 7.5 million, at least 3 million are gun owners. Out of the almost 30,000 students and faculty at Virgina tech, there are at least several dozen, perhaps as many as several hundred CCW holders (I've known more than a couple personally) and several thousand gun owners.

If just one of the students, faculty, or staff there that day were carrying a gun; they could have stopped this mass murder. It isn't assured that they would have, but it's damn well sure that without arms, they were nothing more than cowering victims.

Yesterday, in this post "Blue Girl" called this notion ridiculous, saying that private citizens who are not sworn law enforcement officers are the equivalent of Barney Pfife with his one bullet in his shirt... yosemite sam, backyard rambo, whatever ridiculous insult you want to pile on. Essentially she (and some of her commenters) are saying "you are all incompetent, and mentally ill for thinking you could stop this. You are a danger to yourself and others, leave it to the professionals". She (and some of her commenterS) went on to blame guns in general, the NRA, and gun owners for all "gun violence"; and to suggest that effective gun control could stop things like this from happening. She is of course not isolated in this view; many people share it.

This view is patently ridiculous; and indicates a fundamental lack of maturity, and understanding about criminals, the insane, violence, and the effectiveness of both weapons, and weapons laws.

Firstly, there is no such thing as "gun violence", there are only "people violence", and "natural violence". Guns are an inanimate object, that have no capability to act on their own. They are tools that individuals use, for good or ill; and have no inherent morality.

Second, and what I want to specifically address in this post however; is the idea that private gun owners are somehow incompetent and dangerous, and that police and other law enforcement officers are somehow more qualified, and better trained in firearms and their use.

This view is shared by MANY people, even many people who are otherwise not anti-gun. They believe that police officers are for the most part firearms experts, and highly trained in shooting.

Sadly, in most cases, this is not true. I don't mean to denigrate the many fine law enforcement officers in this country; but most cops are not very good with guns, and most are sadly ignorant of them, both legally and technically.

Let's do a little point-counterpoint here:

Point: I carry every day, all day.

Counterpoint: Most cops carry 8 hours a day (it amazes me that most cops don’t carry off duty).

Point: I carry a $2000 pistol, custom made for me, specifically to be incredibly accurate and reliable. I have several other pistols jsut as reliable (though perhaps not quite as accurate), and I can choose the appropriate pistol for the appropriate situation. I choose my supporting gear to specifically suit my personal, and situational needs.

Counterpoint: Most cops have one gun, often not well suited to their body, or shooting style. It is often maintained only in a basic fashion, and often worn or “loose” to the point of questionable accuracy. Because they are fired infrequently, it is difficult to judge reliability. Most cops are limited in their supporting equipment choices to that which the department issues.

Point: I extensively test all my ammunition options, select those that perform best, and then test those again to come up with an appropriate load which shoots accurately and reliably from my weapon, along with two backup loads.

Counterpoint: Most cops are limited to ammunition issued by their department, generally chosen based on cost; and may be limited to relatively ineffective chambering and loadings, because of cost, and political considerations.

Point: I have hundreds of hours of classroom training in small arms usage, and thousands of hours of range training. I have also delivered hundreds of hours of training to others. I try and take a training class at least every other year (more often if I can afford it), and up until recently was REQUIRED to do so every 4 years.

Counterpoint: Most cops get 8-16 hours or so of classroom training at the beginning of their career, and if they are lucky 24 hours of range training. They then generally get no continuing classroom training with firearms throughout their careers, and at most 8 hours of range training per year (this is starting to improve in some departments).

Point: I shoot 500rds a week in a good month; every other week in a bad one.

Counterpoint: Most cops shoot less than 500 rounds per year... in fact many shoot less than 100 rounds a year. There are some law enforcement organizations which only require a 25 round qualification every other year.

Point: I train to a standard of combat accuracy that requires the ability to put 5 shots into a 4” circle on a moving target at 10 yards (and I don’t always make it, but it’s always close).

Counterpoint: Most cops train to get 70% hits in a 16” x 18” oval

Point: I train with a moving shooter, moving target, and both paper and reactive targets of varying sizes, at varying ranges, indoors and out; in varying weather conditions; strong and weak handed; and I include rapid reloading and malfunction drills in my training

Counterpoint: Most cops “train” at a fixed range, with fixed lighting and weather conditions, a fixed target; and with little emphasis on reloads or malfunction clearance, using only “stock” shooting positions (though this is improving somewhat).

Point: I am not unusual in the community of shooters, in seeking and achieving this level of training and performance. There are 60,000 nationally ranked competitive practical pistol shooters, and many more non ranked shooters, across the various pistol shooting disciplines. There are several times that many competitive rifle shooters. Most of those people also carry concealed on a daily basis. Then there are the many thousands of students taking advanced pistol instruction every year.

Counterpoint: Of the 800,000 full time sworn law enforcement officers in the united states, not 1 in 100 is a “gun guy”; and most of those, are counted among the people I list above. They universally describe their competitive and other non-law enforcement training as many times better than that of their law enforcement agencies, and fellow officers.

So, really, who is Barney Pfife here?

What's worse is, when anti-gun types ask me why I train so much (if they even bother); I tell them that I train because of people like this mass murderer. I tell them that I train, not because I want trouble, but because if trouble comes I don't want to be unprepared for it. I'd rather have it and not need it, than need it and not have it.

When presented with this perfectly valid justification, they say things like "you're paranoid" or "you're a wannabe hero", "you can't protect yourself", "you're more of a danger to the people around you" etc...

WHY?

... Because they don't trust themselves, and project that distrust onto others. Because they are afraid. Because they want to believe that they don't HAVE to have the responsibility of doing the same themselves, they don't have to protect themselves, they don't have to protect others around them. Because they want to believe that the cops can protect them.

Anything that threatens this view creates a violent emotional response in them.

Oh… and one more thing.

Point: It takes a large man an average of 1.7 seconds from a standing, apparently non threatening start, to cross 7 yards (21 feet), and execute a knife slash on another person (a trained shooter can draw and fire in 1.5 seconds - though it is difficult).

Counterpoint: The average 911 response time in this country is 8 minutes

Did you hear that? It is the sound of ultimate suffering...


Monday, April 16, 2007

Mel's Quote of the Day

Mel, upon coming home from her MOMS group:

"You turned Trivial Pursuit into a drinking game?

Chronography

Well, I really need a chronograph... or rather I really need a NEW chronograph.

I have a 15+ year old Chrony F (painted green at least), with CARDBOARD skyscreens. It works, but it pretty much sucks. No memory, no remote, no strings or timers etc... Plus, CARDBOARD screens.

I'm doing some load development, and I really need a good chronograph; this thing just aint gonna cut it.

What I'm wondering though, is whether I should upgrade my current Chrony, or buy a new chronograph; and if I buy a new one, which one should I buy.

Chrony has GREAT customer service; and a fun little upgrade program. You can take any green painted Chrony F1 model (the old red and black models are trade-in only, for a bit more), and upgrade it.



The upgrade pricing is seriously great. I can go to a Gamma Master Chrony for $85, or $135 with the printer (which sells for $95 separately). They’ll take ANY chronograph, even a broken one, as a trade-in on the same gamma master for $114 without, or $158 with the printer.

The gamma master is their top of the line, with the 1000 shot memory, 100 strings, string editing; High, Low and Average Velocities; Extreme Spread and Standard Deviations; remote, timer (with 1000 shot memory and 100 strings), and a PC interface (the web site says the memory is 500 shots, but thats old copy. The gamma master gets the 1000 shot memory upgrade by default).

All in all, it’s a kick ass deal; and like I said, I think Chrony is a great company.

BUT…


I’m also lusting after the PACT Pro Chronograph XP, which runs $199 from midway; and is as much more feature rich than the Gamma Master, as the Gamma Master is to the original Chrony.

You get everything the gamma master can do, plus nice extras like IR skyscreen option, every possible string calculation you can think of, wind drift, ballistic coefficient calculation, Kinetic Energy, Momentum, TKO, and IPSC power factor.

Yeah, that's frikken cool.

The Gamma Master Chrony has a retail price of $200; and honestly, I don't see why anyone would choose it over the PACT (unless they valued the compact nature of the Chrony. It's really easy to fit into a large range bag and the like - which, I admit, is a useful thing). At the upgrade price of $135 however, that's an attractive offer; and the more feature rich chronographs are a lot bulkier and harder to transport.



Then theres competition electronics ProChrono bargain model ($99) and the Millenium, which has a lot of the features of the Pro XP; though isn't QUITE there, for the same price.



So, anybody have any experiences they'd like to share with those, or other models? Opinions? Different ideas?

Parkinsons Law in Action



Click for larger.

Sunday, April 15, 2007

He dunno what he's asking for

Rivrdog tagged all the gunbloggers who read his site with this meme:
All of you neat freaks need not reply, you won't have any of this drek lying on your desk.

Meme:

What calibers/brands/bullet weights of ammo are lying on your desk at your blog station right now?

How 'bout you?

For extra credit, list the knives or edged weapons lying on the blogstation (or within arm's reach):

Hehehe...

My blog station happens to be my loading bench, which includes my boxed ammo storage (bulk ammo is in crates, and SHTF ammo is loaded up in mags, in grab-n-go bags); and within arms reach is my field knife box (collectibles and smaller knives are elsewhere), and one of my swords.

Obviously this is all in a locked and secured area; which I also use as my office.

Ok so, on the bench itself I've got:


100 rounds of boxed handloaded 9mm fmj
200 rounds boxed handloaded .45acp Hornady XTP
100 cases primed 9mm brass
1000 cases primed .45acp brass
2000 cases unprimed .45acp brass
1000 cases unprimed 9mm brass
200 cases unprimed .38spl brass
200 cases unprimed .30-06 brass
500 cast lead .45acp bullets(X-Caliber)
500 plated 200gr SWC .45acp bullets (Berrys)
250 plated 9mm round nose bullets(berrys)
200 185gr Hornady XTP bullets
100 185gr .45acp gold dot bullets
100 124gr 9mm bullets
1000 federal large pistol primers
3000 cci small pistol primers
1lb Hodgdon TiteGroup
1lb Hodgdon HP-38
1lb Alliant Blue-Dot
And in mags:
16+1 200gr speed gold dot +p .45acp
6+1 95gr winchester ranger SXT +p+ .380acp
30 PMC moderator 38gr subsonic hollowpoint .22lr
Loose on the benchtop:
1x Lacquer wolf .225 (I wont shoot the stuff)
2x Winchester 20ga 7-1/2 shot practice loads
1x 240gr Hornady XTP .454 casull
1x 9mm dummy round
1x .45acp dummy round
On the boxed ammo shelves, sorted by chambering:

Shotgun
20ga: 20 buckshot 35 practice shot loads
12 ga: 125 practice shot loads, 60 buckshot, 20 "specialty"
Rifle
.223 Remington: 850rds mixed wolf polymer and PMC, 100 blanks
7.62x39: 300rds silver bear
.308win: 400rds PMC
.303 brit: 80rds Sellier and Bellot
7.62x54r: 100rds Hungarian milsurp
.30-06: 200rds CMP, 40 remington Core-Lokt, Winchester Super-X
.22
.22lr: 1 brick PMC moderator, 1brick Aguila Super Colibri, 1 brick remington subsonic, 150rds federal, 300rds cci (stinger, velocitor, and minimag) 80 tracers, 20 shotshells
Pistol
.380acp: 200rds winchester white box
9x18: 400rds silver bear
9x19: 1000rds nato milsurp, 300 mixed bulk ammo, 10 shotshells 100rds mixed premium (mostly gold dot)
.38spl: 60rds mixed bulk, 40rds cor-bon premium, 20rds federal hydrashok
.40s&w: 330rds speer gold dot, 20rds hydrashok, 36rds glaser safety slugs
.357 sig: 250rds speer gold dot, 60rds hornady XTP, 36rds glaser safety slugs
.45acp: 500rds mixed reloads and practice bulk, 20rds win ranger SXT, 40rds Cor-Bon, 40rds Taurus solid copper, 200rds speer gold dot
.357 magnum: 160rds mixed bulk, 40rds cor-bon premium, 20rds federal heavy solids
.45 colt: 1000rds PMC cowboy loads
.454 casull: 120rds 240gr Hornady XTP
Finally, the "edged weapons" section:

and


1 Ka-Bar Bob Dozier custom fighter
1 SOG Agent
1 Benchmade Prototype Mel Pardue Ambush (from my pocket)
1 Katz BlackKat
1 Buck Black Nighthawk
1 Lynn and Cook custom "Saturn"
1 reproduction 16th century pierced plate swept hilt longsword (halfway between a Schiavona and a sword rapier)

Oh and scattered within reach are an x-acto knife set, two gerber multitools and a bucktool, a Kershaw Ken Onion Blackout, and a couple superknives.
4800rds worth of components, 57rds in mags and loose, and 10,440 boxed up, plus the bulk crates and loaded mags in bags...

Think you've got enough ammo there Butch...

Hell no!

Trying something out

Sitemeter has been very wonky and irritating lately. If I were getting it free I'd have no problem (don't whine about free ice cream), but I have the premium account (it's cheap and useful).

Anyway, I'm going to keep sitemeter, but I've also signed on for google analytics; just to see what it can do for me.

Should be interesting to compare the two at least.

Saturday, April 14, 2007

A Chill..



I saw this picture at Michael Yons site; and it game me a chill.

See, that picture, that looks EXACTLY like my brother at 18. When I say exactly, I mean that if I took his picture (I don't have one of him older than 13) and put it up next to this one, you'd think they were the same person.

Now I don't want to project my brother onto this soldier or vice versa; it's just that the resemblance has really effected me right at this moment.

Not that I would wish life in a war zone on anyone; but his life would have been so much better if had had made a choice to be a soldier, instead of a drug abuser, and a drug dealer.

Now, we don't get along... that's an understatement. The man my brother has become is someone I can't stand, can't be near, and can't have in my life. I can't tell you how much he has stolen from me, and from my mother. I can't tell you the trouble he has caused. He burned my house down on my 19th birthday. He nearly made me kill him two years ago.

...But he's my brother, and I'll always love him.

Next Thursday will be my little brothers 28th birthday, and it's likely to be his last.

A few months ago my brother was diagnosed with an aggressive malignancy in his stomach lining. At the time it was the size of a golf ball, and growing rapidly.

My brother has refused treatment for his cancer.

As of a couple weeks ago, the mass is now baseball sized. He's unable to eat solid food without vomiting, he's vomiting up blood... but of course he's self medicating with illegal prescription drugs, along with certain "recreational pharmaceuticals". He's unlikely to survive more than a few more months.

Apparently he's decided that he wants to die, on his terms, and as high as he can possibly get.

The thing that gets me the most about that pic though, is the eyes. That kid has the stare.

My brother has never been a soldier, never been at war.. up until he started dealing drugs seriously had only seen real severe violence once (when we were kids I was in a fight where to kids died. My brother was there).... But he's had the stare since he was about 13.

He's been angry since he was born, and he's never been able to control it, focus it, or work it out. He has no interest in anything but baseball, and trying to drown his anger and rage and bitterness by getting as high as possible.

...But he didn't have to die. His prognosis was good; his cancer was operable, and with chemo would not have spread. It would have meant some debilitation and pain, and nausea and all the other things that go with cancer treatment.

But he didn't want to. He's chosen to die instead. To some extent I can say to myself, well, he's seen my mothers lingering illness... always declining, but always hanging on, just barely; and he didn't want that...

... But... it's in the eyes you see...

...he doesn't really want to live, and he hasn't for a long time. The cancer hasn't changed that, it's only provided the means.

I've had this conversation... only a little more politely

Scammers Lament

[01:01] shopping_166@hotmail.com: hi,how are you doing?may i have a chat with you?

[01:02] Chris Byrne: Why not, I'm not an idiot, I work in information security, and I find sales pitches amusing

[01:03] shopping_166@hotmail.com: really?what business do you do?

[01:04] Chris Byrne: I consult on information security for banks, medical companies, the government etc...

[01:05] shopping_166@hotmail.com: i see

[01:05] Chris Byrne: I also write about security for various websites and magazines.
[01:05] Chris Byrne: As I said, I find random solicitations amusing. They give me material for my writing.

[01:06] shopping_166@hotmail.com: oh, great

[01:07] Chris Byrne: So, what's the pitch?

[01:07] shopping_166@hotmail.com: sorry,what is pitch?

[01:08] Chris Byrne: Are you selling something, are you trying to get me to fall in love with you and send you money, are you trying to convince me to invest in something, or are you trying to get me to "transfer money" to another country?

[01:09] shopping_166@hotmail.com: but you don't do our business

[01:09] Chris Byrne: What exactly is your business?

[01:10] shopping_166@hotmail.com: sell shoes,clothes etc

[01:10] Chris Byrne: See, there you go, you're selling something.
[01:10] Chris Byrne: One presumes trademarked goods manufactured in china for far below normal prices?

[01:11] shopping_166@hotmail.com: :)

[01:11] Chris Byrne: See, I'm good at this game

[01:11] shopping_166@hotmail.com: you won't purchase,will you?

[01:11] Chris Byrne: It doesn't seem likely

[01:13] shopping_166@hotmail.com: :)

[01:16] shopping_166@hotmail.com: what do you want to do?

[01:17] Chris Byrne: Well, if you have a web site that doesn't try and insert nasty software onto my computer, or steal my personal information, I'll look at it.
[01:17] Chris Byrne: I don't use any browsers with the security holes used for such things, and I visit them using a Linux box so they can't hurt me anyway, but they do tend to be irritating.

[01:18] shopping_166@hotmail.com: thanks.it is your safeness.right?

[01:19] Chris Byrne: Right

[01:19] shopping_166@hotmail.com: ok.i know
[01:19] shopping_166@hotmail.com: see you later!busy now

[01:20] Chris Byrne: Have fun
[01:20] Chris Byrne: I am SOOO blogging this

Friday, April 13, 2007

The "Tramp" continuum

I've noticed lately, that there appears to be a continuum of indicators for "loose" women; starting with the relatively benign and ending up at the "I wouldn't do her with someone else's dick" stage.

Please note, I am not using these terms to denigrate freaks or sluts. I LOVE freaks and sluts (I'm very happily married now, my love is therefore in a theoretical and entirely non-physical sense); and think the world would be better off with more of them. Tramps on the other hand are a cancer on all mankind.

Now, these indicators are not universal; there are perfectly great women who posses them; however it is the imitation of these indicators by stupid, worthless (and I use that term advisedly. They have neither self worth, nor redeeming value), tramps that give them a bad name.

It's also important to note that individually, some of these characteristics are not necessarily "tramp related". For example, there are plenty of people in the body modification subculture who are into such things. Look for a combination of these indicators, without other body modification cues; and generally speaking bleached blonde hair, and frosted or metallic makeup, just to be sure.

I've conveniently color coded the subtitles to indicate degree of danger.

The continuum looks like this:

1. Large number of ear piercings - Ehh, maybe: At this stage, the female in question may just like a lot of earrings; but it's the first step down the road

2. Wearing inappropriate clothing in public - Baby tramp or tramp wannabe: I'm not thinking about short skirts and tight tops... hell everyone wears those now. I'm talking about clothes that say "slut", "porn star", "fuck me like a bitch" "I give good head" etc... in public. Oh, and wearing pajamas or underwear as outerclothes, or extremely age/situationally inappropriate clothing is in there as well.

At one time, this might have been a solid indicator, but these days it's just a fashion trend

3. Belly button piercing - Tramp curious : This one marks them as either into piercing in general, or imitative of the general tramp fashion. Either one is a decent indicator of proto-freaky status (for good or ill). These ones may be salvageable, if steered into slutitude or freakitude, and away from tramphood.

4. The "tramp stamp" - Tramp in training : The small of the back tatoo, often shaped like the thong panties inevitably visible underneath it. This used to be an indicator of the inked subculture, but now every tramp has to have one (thus the moniker).

5. The prominently visible tongue piercing - Trampilicious : There are only two reasons for tongue piercings to be noticable; either because you are just into piercing (again, a good indicator of freakiness), or because you want to advertise that you perform oral sex well. It is perfectly possible to have a tongue piercing without showing it off (I did at one point, but my body didn't care for it); but not for a tramp.

The sad part is, most of the tramps who DO show it off, actually aren't any good at giving head.

6. Nipple piercings - Lookout, this ones trouble : This was once the province of only the piercing fetishists (and pirates and 19t century sailors); but in the last 15 years it has become a mark of extreme tramphood as well. If she isn't a total piercing nut, and she's got her nipples pierced, you can bet she's a tramp. Oh and extra points if any of her piercings are connected by a chain.

7. The clit piercing - Amateur porn here I come : I really think the subheading says it all; if you find a girl who isn't a piercing freak, and she's got her clit pierced... well the lyrics of Buck Cherrys recent hit come to mind "Oh, she's a crazy bitch but she fucks so good I'm on top of it". The clit piercing has become de-rigeur for both porn stars, and the tramps who want to be just like them.



So fellows, heed my warning signs; and involve ye not with the tramps, unless you have multiple layers of latex, and a convenient fake phone number; for they are fraught with stupidity and peril.

Thursday, April 12, 2007

Shooting Pistols Like You Mean It

"Front sight, trigger squeeze"

How many times have you heard that? They're two of the universal fundamentals of good shooting: Maintain sight picture, and trigger control.

Front sight, Trigger squeeze.

I was having a discussion today with a non-shooter, and a casual shooter who hasn't shot since he moved to California (I'll be taking them both shooting some time in the next couple months. They live in CA and visit a couple times a month), and we talked about what it takes to shoot well.

The first part of the discussion was about rifles vs. pistols. Rifles, on the whole are more inherently accurate than pistols are, so a lot of folks aren't much interested in pistol accuracy. Actually a lot of folks seem to think there is no such thing.

The fact is, it's a lot harder to shoot pistols well, than it is to shoot rifles well; because of pistols inherent mechanical inaccuracy in comparison to rifles, as well as the far less stable platform with a shorter aiming radius.

What do I mean "a lot harder"?

Well I'm not talking about sniping, competitive benchrest shooting, highpower and the like. Those are disciplines which need tremendous skill and ability to perform well; and in which the standards of performance are so exacting that any mechanical advantage rifles have over pistols is factored out.

What I'm talking about is the various practical pistol shooting disciplines; as opposed to the casual benchrest shooting that most people do with their rifles (long range handgun shooting, like metallic silhouette, is a very different discipline, with different equipment and parameters; as is bullseye shooting).

The accuracy and precision at 25 yards of the very best practical pistol competitors, with the very best guns; is quite literally 1/10th of what even a relatively casual shooter can do with a half decent rifle (or rather the inaccuracy and imprecision is 10 times that). That is simply the nature of the weapons.

With a rifle, on a bench, with a good rest, and good iron sights; achieving 2" accuracy at 25 yards requires essentially no skill. Providing you don't jerk your trigger or knock the gun offline, any reasonable rifle should shoot into 1" or less at 25 yards.

Any match grade rifle should be shooting into 1/4" or less (5 shots making one large hole) at 25 yards; with only a slightly skilled shooter.

Offhand (standing up without a rest), any reasonable rifle should shoot into 2" or less at 25 yards with just a little bit more skill. In fact, I'd say most rifles and most shooters with just a little training and practice, should still be shooting into 1" or less, even offhand (though it is certainly more difficult than on the bench).

In comparison, most skilled shooters with high end pistols, can't consistently make 2" groups at 25 yards off the bench without a very good rest; never mind offhand (best groupings are another thing entirely. My best 25 yard group ever with a service type pistol, was 4 shots into 3/4" with one flyer opening it to 1-1/4". Groups like that are rare) .

The thing with pistols, is that there are lot more variables and factors working against you. The process of shooting well is the same, but the process of "not screwing up" is more difficult.

So, how do you shoot pistols well... or maybe more importantly, how do you "not screw up".

Well first... how do you define shooting well?

The first thing most people think of when you say "shooting well", is "accuracy". Of course they may not know what they really mean when they are saying accuracy. Some people think that accuracy means good groups, some people think good groups automatically means accuracy. Some folks think shooting close to "the bullseye" automatically means good groups.

Basically, there are two factors to good shooting (actually four, including speed and safety, but two are what most people think of); precision, and accuracy... unfortunately most people confuse or conflate them.

Precision is the ability to shoot into the same spot repeatedly (grouping), accuracy is the ability to put a bullet at (or as close as possible to) point of aim. In a gun fight, accuracy is more important; but in terms of the fundamentals of shooting, precision is FAR more important; because if you can shoot with precision, you know how to shoot; you just need to figure out where to aim to hit the target.

OK, so how do you shoot good groups?

Well, the very factor is the mechanical accuracy of the gun itself. This comprises the direct mechanical accuracy potential (how precise the pistol is capable of being with all other factors removed), as well as the trigger, design of the grip, the chambering, and other mechanical factors (like slide speed, recoil etc..).

The fact is, some guns will never shoot all that well, no matter how skilled the shooter. Some guns are harder to shoot accurately than others. Some guns are so mechanically accurate, and ergonomic, they almost seem to shoot themselves (I'm thinking competitive .22s, pre model 17 K22s and the like).

The second factor is consistency. Grouping well is about doing the same thing, the same way, EXACTLY, first time, every time. Breathe the same way, acquire the sight picture the same way, and settle it on the exact same point of aim, the same way.

A common rookie mistake, is to unconsciously shift your point of aim to the bullet hole you just made. DONT’ DO THAT. Right now you are trying to learn how to be consistent; after that you can figure out how to be accurate.

Very important, SLOW DOWN. When you’re shooting for group (or for accuracy), take your time. Take 20 or 30 seconds for each shot if that's how long it takes you to get settled in (actually probably not that long. If you take too long errors can creep in). Shoot as slow as it takes for you to get into that same groove every time.

The last factor is technique. Now, there are a hell of a lot of ways to shoot a pistol, and a hell of a lot of opinions and variations on those techniques. Different techniques are appropriate for different people, different guns, and different situations.

The thing is, there is no "one right way"; everyone is different, and every situation is different... but there are some fundamentals that apply to almost all techniques; and are just good basic skills. If you have the fundamentals down, you can adapt to different situations as you need to.

The Fundamentals of Pistol Shooting

First fundamental - Safety: Nothing ruins your day faster than shooting something you didn't mean to; or worse, shooting someONE you didn't mean to.

Safety is the most important fundamental of shooting. If you aren't safe, I won't shoot with you, or anywhere near you; and you shouldn't be shooting. I won't deny anyone their right to self defense, but with rights come responsibilities; and you have a responsibility to be safe.

Now, there is a lot more to gun safety than the "four rules", but they are good and important rules; and I think the most important, most fundamental (theres that word again) elements of firearms safety, and they should be understood and followed appropriately by all shooters at all times.

The four rules are:

  1. All Guns are ALWAYS loaded

  2. Never point a gun at anything you are not willing to destroy

  3. Never put your finger on the trigger until you are ready to shoot

  4. Always be sure of your target, and what is beyond it.

Second fundamental - body position and stance: Different people, prefer different stances; and different shooting situations may require different stances; so don't assume there's "the one true stance". You choose what fits you, and the shooting that you are doing.

Whatever you do, chose a relaxed, natural, stable stance; that doesn't fight against your natural muscle mechanics, or skeletal support.

Easiest for beginners or for shooting offhand groups, is a basic isosceles stance. This is a stance where your feet are spread apart slightly more than shoulder width, and square to the target. Your shoulders are square to your feet, and you extend the pistol exactly centered along the midline of your body, evenly supported by both arms; with your elbows straight but not locked. Do not lean back (you may want to lean slightly forward but most recommend keeping your nose over your toes, or your shoulders over your toes at the most), and do not bring your eye down to the sights, bring the sights up to your eye.

Important to any stance, is making the gun an extension of your body. When you have established your stance, the weapon should move with you. Don't move the gun, move your body; and you will be smoother, more accurate, faster, and safer.

Third Fundamental - grip: Again, there are a lot of different preferences among shooters, as to shooting grip. Whatever you chose, you need to have a firm, consistent grip, that maintains control and position throughout the shooting cycle.

Establish a grip that has as much of both hands firmly wrapped around the gun as possible, and grip firm, but not hard. Gripping the gun too hard is one of the most common mistakes of beginning shooters (as is gripping too soft and not controlling the gun). Don't get all white knuckled or have your arms shake. Remember, every twitch in your hands goes directly into your bullets.

You may still hear folks saying "Hold it like a dove" or "like a kitten" or "like a womans breast"; by which they mean just firm enough to be in control, but with as little pressure as possible. This reduces that tendency to shake or twitch.

When you are hunting, or slow fire bullseye shooting (where rapid repeated pistol shots aren't emphasized), this may be a good technique. Over the last 35 years of practical pistol shooting competition however, shooters have found that in general, a very firm, and very controlled grip, is better for recoil control and followup shooting.

I personally prefer the high forward thumb over thumb grip (I’ve described it before on my blog), because it allows for rapid recovery and recoil control; for fast followup shots and transitions.

Remember, the point here is to make the pistol an extension of your body. There should be NO independent motion of the gun; if the gun moves, your body moves; if your body moves the gun moves.

Fourth fundamental - breath control: Do something for me. Take your arm and make a gun shape with your hand. Now extend your arm straight out, and aim along your finger.

Now, keep your arm locked in position, and take a couple of deep breaths.

How much did your "sight picture" change, at the top and bottom of your breath?

This is why breath control is important. As I said in the section on grip, every twitch you have in your body is transmitted directly to the flight of your bullets. Breathing is a surprising amount of motion, that you don't notice when you aren't specifically paying attention to it (like just about everybody). That motion can and will be transfered to your gun to some extent, no matter what you do. The trick it to control it, and even to use it to your advantage.

Slow down. Breathe full but not "deep" breaths. Breathe slow. Then, when you are set, ready, and have your breathing regularized, fire on the same part of your sloooow breathing cycle each time. You can either breathe deep in and hold at the top, and fire; breathe shallow and hold in the middle and fire, or breathe out and hold at the bottom and fire; but whatever you do, hold that breath through the followthrough of the shot (that followthrough is important, and we'll get to it in a bit).

Fifth fundamental - sight picture: You can't hit what you can't see; and you can't hit what you can see, if you can't figure out what direction you are pointing in (instinctive point shooting aside - that's not about grouping, it's about shooting to survive in the close and nasty).

Now, there are a lot of different sight types out there; but they all have the same goal: align the font and rear of the barrel with your eye, and with the target, in a straight line (Yes, the bullet actually shoots in a curve. We havent figure out how to make your eyes see in a curve;that's why point of aim changes over different ranges. The best we can do is a straight line at a known range).

The most common type of pistol sights are "partridge" style open sights, which have a front sight blade, and a rear sight notch. You align the blade in the notch to show the weapon is aligned; and set the target either on top of the post (dotting the I) or through the top of the post (crossing the T); depending on the particular sight type, and the distance to the target (some sights are calibrated so that the point of aim is set for 10 yards shooting on top of the sight, and 25 yards through the top for example).

Aiming should always be done with your body as a whole, not by tilting or twisting the gun. Once you establish your grip and stance, you aim the gun by twisting your body from your hips, and bending from your hips or shoulders. You bring the sights up to your eyeline, don't bring your head down to the gun; and line everything up.

Now, with iron sights, the important thing is front sight focus. The front sights are hanging out there in the breeze, and that's where the misalignment really creeps in. What front sight focus means, is that the FRONT sight is your aiming reference, and your eyes natural focus point. The rear sight and target should be visible, and aligned, but should not be where your focus lies (this can be very hard for people who are nearsighted, who have bifocals, or who are severely astigmatic. They make special glasses that help for those who have these problems).

Look through the rear sights, focusing on the front sight, and aligning the top of the front with the top of the rear, exactly centered in the notch, and with no canting (presuming partridge style sights as most pistols have) or twisting. Do not focus on the target, or the rear sight; keep the front sight in sharp focus, and align the blurs of the rear sight and the point of aim.

Again, the point here is consistency. Point the gun at the same spot, using the same sight alignment, each time, every time. I cannot emphasize this enough, I've said it several time already, but I'll say it again: AIM WITH YOUR WHOLE BODY. The pistol should be locked in as an extension of your body, and you aim from the hips shoulders, with the pistol solidly fixed in your hands.

Sixth fundamental - trigger control: Remember what I've said about motion. Every motion of your body is transferred to your bullets in flight. The one motion you HAVE to make in the shooting process, is squeezing the trigger. It is important to do so gently, smoothly, and CONSISTENTLY.

Don't put your finger on the trigger until your sights are roughly aligned , and you are ready to fire. At all other times, index your finger along the frame or the trigger guard.

When you are ready to fire, rest your finger, (either the very tip, the pad, or the first knuckle crease, depending on the trigger type and weight - try out all three to see what works for you) on the center of the trigger (or just below it - never on the top, or bottom), check your breathing, make your final sight alignment and hold that position, feeling, and spot, while you squeeze through.

Squeeze through.. what does that mean?

Most people who haven't received firearms instruction think "pull the trigger". The problem with "pulling" the trigger, is that it also pulls the gun, usually down and to the right just a bit. Remember, any motion of your body, means motion in the bullets right?

The point of a trigger "squeeze" as opposed to a trigger pull, is to have a smooth, consistent, linear motion. When you're pulling, you're moving your finger back and a bit to the side, which moves the gun back and to the side. When you're squeezing, all your doing is tightening up your grip on the gun with one more finger.

Now, another experiment. Take your hand, and make a loose gripping shape with it; like you were holding the butt of a pistol. Now, squeeze your trigger finger in towards your palm. If you're like 99% of all human beings on the planet, all your other fingers squeezed as well. When you're shooting, this will tend to pull the gun off line a bit.

This is called reflexive motion, and it is natural, automatic, and impossible to eliminate completely; but you can train your way out of almost all of it, to the point where a firm squeeze just firms your grip up a bit; and with proper grip won't pull the gun off line significantly.

When you squeeze the trigger, what you are looking to do is impart the minimum force necessary to do the job, in a way that doesn't move the gun too much. That means use the finger position that gives you the most power without jerking of moving the gun; and squeezing straight back.

Generally speaking you want to squeeze all the way through from takeup (where the trigger starts to give resistance) to break (where the trigger releases) and overtravel (the small bit of motion after the break). Overtravel actually reduces accuracy, because any motion of the trigger after the sudden release of pressure from the break, is going to throw the gun offline; but trying to stop overtravel with your finger will actually make the problem worse (you stop overtravel with a good trigger job, and an overtravel adjustment stop; and it makes a HUGE difference in the feel of the trigger and often the precision of the weapon).

Some double action shooters prefer to "stage" or "set" their trigger pulls; bringing the trigger back to a point just before the break, holding there for a moment to reset the sight picture, and then squeezing through jsut like a single action trigger. The technique can work very well in some weapons, with experience; however it is not something you want to do unless you are on a range, very aware of safety, and very familiar with the mechanics of your weapon; because it's very easy to both pull the gun offline, and to fire when you are not ready (which means you could shoot something you don't want to).

At all stages of the trigger pull, you need to maintain your front sight focus, and sight alignment. Hold that sight alignment through your squeeze, and all the way through the followthrough.

Seventh fundamental - followthrough: Another common rookie mistake is to assume that once you pull the trigger, your job is done.

Dead Wrong.

The shot isn't over until the bullet hits the target, and you've recovered and are ready to shoot again. VERY IMPORTANT, hold your sight alignment, stance, breathing, and trigger control, all the way through the shot, and through recovery.

If you've established a good grip, and a proper stance; recoil control is easy (with practice... lots and lots of practice). You aren't trying to fight the gun, or the recoil; you are just trying to maintain control. Use your grip, and your musculo-skeletal support, to flow with the recoil; but also to restrain it. Your entire body should be acting like a firm shock absorber; and your natural grip and stance should return you to the same point of aim that you started with; just resetting like a spring loaded machine.

With the aforementioned "lots and lots" of practice, it is possible (though not exactly a great idea on the range), to empty a 1911 (8 rounds), in a series of 4 controlled pairs (doubletaps), in less than two seconds; and have them all impact within 4" or less at 10 yards.

That isn't a result of superhuman skill, it's the result of proper stance, grip, and trigger control, making followthrough and recoil recovery automatic; resetting naturally to the correct shooting position each time.

Let's say it one more time: The shot isn’t over when the round goes off, it’s not over until the bullet hits the target, and you’ve recovered from recoil and are ready for the next shot.

LETS REVIEW THE FUNDAMENTALS ONE LAST TIME:

Do EVERYTHING the EXACT SAME WAY, first time, EVERY TIME.

  • Safety

  • Stance

  • Grip

  • Breath control

  • Sight picture

  • Trigger control

  • Followthrough
Finally, remember, SLOW DOWN; you can’t miss fast enough to win.
Thats it... Simple really. Simple... but not easy.

Wednesday, April 11, 2007

Loading Up

Note: This post started off as just doing a costing on progressive reloading, but I decided to expand it into a comprehensive look at the costs and benefits of reloading.

So, the question has been asked, repeatedly by me in my own mind, and in comments; what's the value proposition of reloading; and further, what is the value proposition of a progressive press vs. loading with a single stage or turret press.

Most people who reload get into it, because they want to shoot more, and ammunition is expensive. Some people get into it because match grade ammo is REALLY expensive, and if you get very good at reloading you can make it better than the factories can by far. Some people just do it because they enjoy it; or they do it because they enjoy it, because ammo is expensive, and because they want better accuracy and precision (I'd be one of those folks).

Well, you can get all of that... though maybe not at the same time.

Let me just say up front, for most people, when you reload or handload, you probably won't save much money; you'll probably spend as much as you did before, but you'll shoot a LOT more, and at least a little better... (and that's justification enough on it's own as far as I'm concerned).

...Unless you're like me (or the guys way more hardcore than I am) who shoot hundreds of rounds a week that is. We shoot more, AND save money... mostly because at some point there's a limit to how much you can shoot; you run out of daylight, your hands get tired, your eyes get tired, and your shoulder gets sore.

I have five main goals in reloading.

1. To be able to make enough ammo, affordably, that I can shoot 'til I can't shoot no more, at least twice a month, and preferably every week; without running out of ammo, or having to buy some at the local WallyWorld or Sportsmans warehouse.

2. To be able to make ammo that each of my guns finds particularly accurate and precise; because all guns shoot differently.

3. To have huge quantities of generic ammo that shoots reasonably well on hand, as trade goods and in case of emergencies; without breaking the bank. It used to be you could depend on Mil-Surp for such things, but the prices these days are not much better than reloading, if you can even find it (there has been a major drought in 5.56 and 7.62x39 for the last three years, because of commodities price increases, and because of the GWOT)

4. To be as self sufficient as possible, for whatever reasons there may be; and being able to make my own ammunition is part of that.

5. To know and understand more about firearms, ammunition, and ballistics; and to have fun doing it.

Alright, those sounds like good goals, but how does that translate into real life costs, effort, and time?

I suppose the first question is, what are the direct costs of commercial ammunition, vs. the direct costs of reloading.

Man... ammo is expensive, and with the commodities crunch (copper and tin have been skyrocketing the last few years, and that's primarily what rounds are made from), and the war taking up excess production capacity, it's just getting worse.

For simplicities sake, lets stick with just one load, in one chambering. The most popular commercial round, as well as the most commonly reloaded round is by far .45acp (for many reasons), so let's stick with that (rifle loading can save a hell of a lot more money, but the costs are so highly variable it's difficult to quantify).

These days, a box of 50 230gr FMJ rounds in .45acp, with brass cases (staying away from steel or aluminum, for MANY reasons) runs between $13 and $16. This is up about $2-$3 a box from two years ago. If you buy it by the 20 box case, over the internet, you are looking at something on the order of $280 to $300 shipped.

Basically, an average of about $0.30 a round.

A box of premium defensive ammo like CCI Gold Dots or Hornady XTPs, will run you about $18 a box of $20, or maybe as little as $14 if you buy online. In 1000 round case lots you're talking about $450 to $550.

Call it $0.50 a round.

Working in 1000 round lots is convenient for reloading, because that's typically where the first real price break hits on components. Leaving aside the question of equipment (which we'll address later on in this article), let's look at the cost of those components:

1. Brass: Brass cost is the most highly variable portion of the equation. You have several options for acquiring you brass to reload.
  • New unfired brass in 1000 round lots can be had for anywhere from $0.12 to $0.20 per case. Typical prices would be somewhere around $0.13-$0.14 . 'Course that's not really re-loading, it's handloading.

  • Commercial once fired brass (just like it sounds, it's brass that has been fired once, then cleaned and resold to you) generally runs from $0.06 to $0.08 a round.

  • Bulk sorted fired brass (sorted by caliber not quality) can run as low as a penny a round, but more typical would be $0.025 to $0.05 per case. I typically buy this bulk brass, and pay about $0.025 per case. The only problem with that is, sometimes you get inconsistent quality, and you don't know how old or how many times the case have been fired. So I never load high pressure rounds from unknown brass. I only load +p loads from known once fired or known good brass; and I only load +p+ in new +p rated brass.

  • Buying commercial ammo, shooting it, and recovering the brass is the most expensive way of getting brass as a reloading component; but recovering OTHER people fired brass is free.. minus the back aches from bending over so much.
Oh and rifle brass, just so you know, is MUCH more expensive; anywhere from twice the price, to 10 times the price. Of course it's also a lot tougher, heavier, better made, etc...

Then you also have to take into account, brass is a re-usable component; you can't just look at it as a one time expendable cost. Pistol brass is good for anywhere from two to about 20 reloads Some people will reload a case more than that, but I start noticing thinning and defects after 4-6 reload cycles in some loadings, and personally I don’t think I want to take those chances. For estimation purposes I generally count a piece of brass as good for 10 loadings.

2. Powder: No powder, no boom. No boom, no fun. Buying powder by the pound isn't exactly the best way to get a good price, but it's convenient; because 1lb of most popular pistol powders, makes about 1000 rounds of .45acp. 1 pound powder prices run anywhere from around $11 to around $25, but typical is somewhere around $15.

You can save money buying powder in 8lb kegs, but you don't save all that much, and 8lbs of powder is a LOT, unless you're doing serious bulk loading (8lbs should load up something between 6,000 and 10,000rds of .45acp. that's more than most people shoot in a year, or even two or three years).

3. Primers: Conveniently, primers are sold in 1000ct cartons(with individually sealed 100ct. boxes inside), at anywhere from $15 to $25 per carton (if you buy 5 or 10 boxes you get bigger discounts). This is up by as much as 50% from three years ago. Right now, a typical 1000ct price for large pistol primers would be $20.

4. Bullets: Bullets swap places back and forth with brass for the most expensive part of the round; but of course bullets aren't reusable. They are also a HIGHLY variable cost.
  • If you want to cast your own bullets, you can get down into the $0.01 per bullet, or $10 per thousand range.

  • Commercial plain hardcast bullets run as low as $0.03 per bullet up to about $0.05 in thousand count lots, so somewhere between $30 and $50 per 1000. I typically pay about $45 per thousand.

  • Plated bullets are copper or cupro-nickel plated cast or swaged lead. They are "better" than plain cast lead bullets, but "not as good" as jacketed. I use scare quotes there, because realistically they aren't any better or worse, except that it takes a REALLY good plater to get consistent plated bullets. They leave less lead fouling than lead bullets, but more copper fouling than jacketed; and they are softer than jacketed, so they may not feed as well or stand up to dings as well etc... Anyway, they run from $0.06 to $0.10 per bullet, or $60-$90 per thousand, and I typically pay about $70 per thousand.

  • Bulk jacketed FMJ and bulk JHP bullets are pretty much the same as are used in commercial FMJ and JHP ammunition. In fact in some cases they may be the very same bullets from the same production line. They run from an absolute low of $0.09 per all the way up to $0.18 or so; but typical would be $0.11-$0.14each, for $110 to $140 per thousand. I usually pay $120 to $130.

  • Premium JHP components are available in the Speer Gold Dot, Hornady XTP, and Winchester Silvertip lines (among others); in case you want to make your own defensive or hunting ammo, or duplicate the commercial loadings on your own for practice purposes (which is what I do frequently). They run from about $0.13 each to $0.20 each, but typical would be about $0.16 each, or $160 per thousand.. note, this isn't much more expensive than the standard bulk FMJ.
Note, if you have a local caster (or other bullet manufacturer for that matter, though the discounts aren't as good as on cast lead), you can often get a MUCH better deal (as in half the price) buying in 10,000ct lots. Shipping costs on bullets are a major portion of their expense, and in larger lots the shipping and handling costs become prohibitive (10,000 230 grain bullets weighs 330lbs plus the weight of packaging, and lubricant).

So, totalling that up, you are talking about anywhere from about $50 per thousand, for making your own cast bullets, and reloading your range cases 10 times; to $215 per thousand for once fired brass and commercial bulk FMJ (but counting the reloading of the brass it's actually $160 per thousand); all the way up to about $330 per thousand for premium JHP in new premium brass (and again, if you amortize the brass cost it's $205 per thousand).

Just taking those two cases, as the best comparison against commercial ammunition the numbers break down like this:





TypeReloadAmortizedCommercialInitial savingsAmortized savings
Bulk FMJ per 1000$215$160$300$85$140
Premium JHP per 1000 (new brass)
$330$205$500$170
$295

And remember, that's doing very direct comparisons. If you use plated bullets instead of FMJ, you're talking about $50 less, for $165 per thousand, and $110 per thousand amortized. That's only $0.11 a round, about 1/3 the cost of commercial FMJ; for a savings of $190 per thousand. For bulk practice ammo, there is really no reason not to use the plated, excepting that it takes a few more minutes to clean your guns.

Switch to range brass, and you save another $0.35 per thousand. The cheapest you can get without actually casting your own bullets, is something like $105 per thousand rounds, and $85 amortized; or just 8.5 cents per round. Casting your own bullets drops you another $35 per thousand.

The biggest savings is definitely when you handload for premium loads. Even using the most expensive possible components, you are talking about a $300 savings per $1000. Switch to cheaper brass, or reload your premium brass more than ten times, and as I said above you drop your costs a LOT. The price difference between new premium brass, and range brass is $110 per thousand.

Of course, the direct cost of components is only one part of the equation, you still have to take into account the cost of equipment, and the time it takes.

Honestly, if you understand economics at all; the time is actually the far more important cost.

So, how much time does it take to reload?

Well, that's a complicated question, dependent on process and equipment, and just personal habit.

There are three primary equipment sets of loading large volumes of ammunition:
  • Single stage, single station press: This is a press which has one shell holder, which rams directly into one single working station with a die in it. They are the least expensive option, and generally the strongest, but they are also the slowest.

  • Single stage, turret press: This is a press with one shell holder, but multiple workstations. They are faster to load with, but a little more expensive, and not quite as strong as the single station presses

  • Progressive press: This is a press with a shell plate that holds multiple cases, and rams up into multiple dies simultaneously. The shell plate rotates with every pull of the lever (either manually or automatically) to advance each round

So, which should we use? Well that's a complex question too; and it's very strongly related to your process, and your budget, and what your time (and aggravation) is worth to you. In this case, your process and your equipment are very closely connected.

Single stage presses (turret or fixed) are cheaper, and simpler. Progressive presses are expensive and complicated, but they produce ammo a lot faster. In my case, even when I do pick up a progressive press, I’m going to keep my Lyman turret press running for small batches, load testing and development, and for precision reloading with individual weighed charges. Progressive presses aren't exactly conducive to small batches and such.

With a single stage singe station press, you have to change the dies between operations. This means you spend a lot of time re-adjusting things, and re-checking things. Even with batch processing (we'll get into that in a minute), you spend a lot of time, effort, and trouble just resetting things between operations. With a turret press though, you have up to seven workstations (with a Redding T-7. Most presses have 6 stations, some 4 or 5), and can easily and quickly move between operations without resetting anything.

Since we're talking primarily about volume loading here; to my mind the decision comes down to a turret press, or a progressive.

With just a quick glance at both types, you would think there would be no question; but you would be surprised at how much volume you can do with a good turret press (or even a single stage single station for that matter). The way you do this, is with batch processing; where you set up to run off a large batch of ammunition all at once.

Now, Dillon claims 500-600 rounds per hour with the RL550, and 800 to 1000 per hour with the XL650, and those aren't just made up numbers. Having used both presses before I'll tell you, if you're just straight crankin' you can really do it.

So really, how fast can you load with a turret press? Well, we need to go back to the process question.

The first question is, are we talking rifle or pistol? Because reloading for rifle involves several additional steps; and most of the steps that it shares in common with pistol loading generally take longer.

The slowest process are case prep, and dealing with powder.

Bottlenecked rounds (as most rifles use) require case lubrication for sizing. With straight walled rounds you can just use a carbide die straight with no lube (in fact lube could damage the brass). Then once the case has been sized and deprimed, you need to clean the lube off, to prepare for the next steps.

When you fire a bottlenecked round, the brass "grows" just a bit, making the case slightly longer. After a few firings (or sometimes just one), you have to trim each case neck, then deburr and chamfer the case mouth. Some people also turn the case neck so it has a consistent inside and outside diameter and thickness (which improves the consistency of each round).

If you're reloading military brass (common for 5.56, 7.62n, and .30-06 - the three most commonly reloaded rifle chamberings in this country, with .30-30 as the fourth and .270 as the fifth), you have to swage out the crimp put into the primer pocket. You may want to normalize the primer pockets with a primer pocket and flash hole reamer and deburring tool.

Then finally you need to clean the primer pocket, flash hole, and case neck.

Only then will you be ready to load the empty cases; whereas with pistol rounds, to reach the same stage you just need to deprime and size (though some folks do the primer pocket normalization with pistol rounds as well).

Sounds complicated right? Well, it is, but it's not as bad as it sounds if you have the right tools; or if you aren't trying to go for maximum accuracy. RCBS makes three tools that combined do all of the additional steps above, in just a few seconds each case; but those seconds add up.

De-capping (another word for de-priming) and sizing a pistol round takes about 5 seconds from bin to bin; and in most cases it's the only case prep you do other than cleaning (overnight in a tumbler, so theres not a lot of manual time involved). The case prep for a rifle round takes between 30 seconds and a minute, even without turning the neck or swaging the primer pocket.

On the powder side, unless you are loading bulk .223 practice ammo, you are probably going to want to weigh each charge individually; to improve accuracy, and to insure against squibs and overpressure loads.

With a pistol, charge weight consistency down to 2/10th grain is sufficient (excepting max pressure loads); and is easily achievable (with periodic consistency checks) with a good powder measure like the RCBS uniflow; presuming the right powders anyway (some powders won't measure consistently in a volumetric measure no matter what). It is somewhat more difficult to maintain such consistency from a measure with the much larger charge weights most rifle cartridges use; and rifles are significantly more sensitive to charge weight variations when loading for accuracy.

Just for an example of what I'm talking about, the popular 6mm family of benchrest cartridges have charge weights in the 30-40grain range, behind 60-130gr bullets. With a 30gr charge behind a 70gr bullet, 2/10th grain variation is only 1/2200th of an ounce, and less than .7% of the charge weight; but can throw a loads groups off by 1/4 minute of angle or more at 100 yards; and far more at the ranges used in competitive benchrest shooting (up to 1000 yards in formal competition, more in informal). 1/4 minute of angle doesn't sound like very much, it's about 1/4" at 100 yards; but it's 2.5" at 1000 yards, in a competition where the winning group size may be 1.8"

Finally, again unless you are producing bulk practice .223 or something similar, you generally aren't going to loading the same volume of rifle ammo as you would be pistol. In a range trip where I may shoot 500rds of just .45acp, plus all my other pistol shooting; I'll typically only shoot 20 to 200 rounds from various rifles... excepting ARs in .223/5.56 which as I've repeatedly referred to above, is a little bit different (unless I'm loading match ammo I treat it much like pistol), and where I'll easily go through 10 or 15 20 or 30rd magazines.

Given these factors, I would generally load rifles in a slower, more focused, and more quality and consistency oriented process, with a lot more individual checks; so I'm not really too concerned with the speed of reloading rifle rounds, except to note that it typically takes at least twice, and maybe as much as three or four times as long as to load the same amount of pistol ammo.

Honestly, I figure most other reloaders are the same way. They reload pistol for speed (and economy) and rifle for accuracy (and economy). Unless as I've said you're loading large bulk loads of .223, in which case you treat it like pistol ammo; or unless you're a competitive benchrest shooter, or high power competitor. Of course if you are either of those, 1. you're insane (but in a fun way) and 2. you're going to be spending the individual time and effort more appropriate to a swiss watch on every cartridge anyway, even if you ARE making 500 of them at once.

Given all of that; I don't see any real advantage to a progressive press over a turret press.

So, for the purposes of this discussion, lets focus on pistols. How fast can you load for pistols using a turret press?

You get a wide variety of answers on this one, seemingly a different answer from every reloader you ask; but on the low side it's about 100 rounds per hour, and on the high side, it's about 200. Honestly, I'm not sure how you could manage 200, you'd have to be incredibly fast and efficient, but you can get pretty close.

I can usually punch out 100-150 an hour on my turret press. If I were to really batch up and just crank I could probably do about 170-180; but that would be non-stop continuous press action. Personally, I don’t feel like making my arms that sore.

First thing, what equipment am I using currently (I've been over this before, but lets get it out here again just for the purposes of this discussion), and how much does it cost? :

1. Lyman Spar-t turret press
2. RCBS carbide dies
3. Lee auto-prime
4. RCBS Uniflow powder measure
5. Lee Safety scale ( I REALLY need to buy a better scale)
6. Various loading blocks (MTM, RCBS, cartridge box inserts, drilled blocks etc...)
7. Lyman dial caliper
8. Frankford arsenal vibratory case cleaner (with corncob media)
9. Cheap media separator (I'm thinking about the Dillon one)
10. Reloading manuals from Lyman, Speer, Hodgdon and others

The total price for all of the above, if I'd had to pay for the press and dies (which I didn't); would have been about $400.

Now, with how much it costs out of the way; how much ammo can you make, how fast, with a setup like that?

Well, like I said, the way to do this quickly and efficiently is with batching. Each step is done en mass with as much brass as you feel like running through at once, to keep the operations flowing.

Second, what's the process of reloading? What are those operations and how do they work?

From the outside, reloading looks like complicated black magic, but really it's very simple. Very precise, but very simple.

The most important things in reloading are precision, consistency, and safety. Do the same thing, the same way, each time, every time; and you'll produce good ammo. Don't do that, and you'll make bad ammo, or even blow yourself up. Dire warnings aside, precision and consistency help you make ammo faster, more accurate, and cheaper.

The actual process is very linear, and easy to understand and break down into steps, as follows:

1. Clean and inspect your brass: While it's not necessary to get brass all shiny and new looking (though most reloaders I know of LIKE to anyway), the brass needs to be clean, free of grit on the outside, and free of excessive powder fouling on the inside. The best way to do this is with a vibratory or rotating case cleaner, with corncob or walnut media, and possibly some case cleaning additive.

All you do is dump your collected fired cases into a sieve to screen out loose dirt, then dump them into the case cleaner with the cleaning media; and turn it on. A few hours later, and your brass is cleaned, and ready to be sieved out again to get the media off. They make rotating tumblers that make quick work of this.

Once you've cleaned them out, you give each case a quick inspection; looking for splits, burrs, large dents etc.. Anything that cant be immediately and easily corrected, or would indicate a structural weakness, means that case is discarded (preferably crushing it first so it isn't accidentally re-used)

2. Size and de-prime: This process is very simple. You place a round into the shell holder, and pull the lever, to force the cartridge up into the sizing/decapping die. This die has a hardened ring which forces the brass down to the proper size; and a hardened pin in the middle which pops the primer out of the flash hole.

3. Prime: In this stage you insert the primer into the primer pocket in the head of the case. Some people do this with an attachment on their press, or as part of the progressive process; but I personally prefer to use a manual priming tool because it gives you better control and feel. You simply place the primers inside up into the tray, insert the shell into the shell holder, and squeeze.

3. Expand: In this stage, you switch dies to the expander die, which "bells" the mouth of the case, in order to make it easier to insert a bullet. Some expander dies are hollow and allow you to charge the powder through them in this step.

4. Charge: In this stage you measure the powder out, and pour it into the case. You can do this with a scale and a funnel, with a dipper, or with a variable cavity powder measure. BE VERY CAREFUL HERE. This is where a screwup can blow guns up the easiest.

5. Insert a bullet into the case mouth: Once you've place the powder into the case, you want to cover it with a bullet as quickly as possible to avoid contamination, or spillage.

6. Seat and crimp: Insert the case with a bullet on top, the powder charge inside, and the primer on the bottom; into the shell holder. Pull the lever to ram the cartridge up into the seating die. The seating stem will push the bullet into the case the correct depth, and then the die will squeeze the mouth of the case down onto the bullet, locking it into place with friction (or with some dies and some bullets, with a mechanical fit of the case mouth into a groove on the bullet called a cannelure).

Now, as to how long this whole process takes, well, I’ve timed all this; because I’m a little too anal.

I like to pre-clean overnight and then sort, inspect, de-cap, and size my brass in large lots. I usually do several hundred at a time, and I can do about 500-600 cases an hour. This operation tends to be pretty mindless, and I just start cranking until I’m done.

...Yeah, those times my arm ends up a little sore. I did 1500 in one go once; and MAN I was sore the next day. Three hours of nothing but the same motion, with a non-trivial effort (I use an older press, without the compound leverage ram that newer presses use. It takes a lot more effort to de-prime and resize those cases)

From there, I hand prime all the cases for the run using my Lee auto prime, and stage them into loading blocks. I can do between 900 and 1200 an hour if I'm really going at it. The most I’ve done at once was 500, and it took me a little less than half an hour. A more relaxed "typical" speed would be something like 500-600 an hour. I did 250 last night while watching "the Dresden Files" and it took me about half an hour.

I like to do the priming step watching TV or somesuch. Something where I'm not exactly distracted, but my mind is occupied, so I don't get hypnotized by the process. You actually make less mistakes that way, than with absolutely no distractions. I stage the brass primer side up into loading blocks, so I can easily verify by sight and touch that each case has an evenly and properly seated primer.

Then I expand all the mouths, and stage back into the blocks which also goes at between 900 and 1200 an hour. Again, the most I’ve done at once was 500, and it took a little less than half an hour; and at a more relaxed pace I can do 500-600 an hour.

Next, I throw the charges into each case in the loading blocks. I can do 50 in just over a minute; but then I need to stop to verify the charge throw (never go more than 50 charges without verifying), which takes about 30 seconds or a minute. Let’s call it 100 every three minutes, or about 2000 per hour. I never do more than about 200 at a time without resting though; this is something you really don’t want to screw up on. After a couple minutes of doing something else, I go back and throw another 200. So again for a more relaxed pace call it 1200 an hour.

The good thing about loading into the blocks like that, is that you can verify the charge levels visually very easy.

Once the charges are verified, I place bullets into each case in the blocks; and I can do about 900-1200 an hour, even at a relaxed pace. It really only takes 2 seconds to put a bullet on the case mouth, and you just pop them on row by row.

Finally, I seat, crimp, and box the rounds; at about 900 rounds per hour.

So, let’s presume 500 rounds, batched, total production time.

1. Inspect, decap and size: one hour, to 90 minutes
2. Prime: 30 minutes to one hour
3. Expand: 30 minutes
4. Charge: 15 to 20 minutes
5. Insert bullet: 15 minutes
6. Seat, crimp, and box: 30-45 minutes

So, at full speed, I can probably do 500 rounds, in three hours; for about 170 rounds per hour. Of course if I did I’d be sore and exhausted afterwards. At a more relaxed pace it would take about four hours, for a total of 125 rounds an hour.

Personally, other than de-capping and sizing (which as I said, I like to do several hundred at a time), I really don’t like doing more than about 250-300 rounds at once; and at a more relaxed pace I can do that in a little less than 2 hours.

Now, if I had an RL550, I could do at least 3 times that level of production at my FASTEST pace, and maybe 4-5 times that with an XL650; and I wouldn’t be near as sore or tired.

...But, it would be expensive, and rather fiddly.

Just looking at new pricing, here’s what an xl650 setup, just for .45, would run me:

1. XL650 press, with .45acp caliber kit - $489.95
2. Case feeder with large pistol plate - $194.95
3. Powdercheck - $63.95
4. Powder sensor - $39.95
5. Roller handle - $32.95
6. Strong mount - 39.95
7. Bullet tray - 35.95

It totals out at just under $900, plus tax because I live in AZ (Dillon is in North Scottsdale, I'm in south Scottsdale).

The RL550 is a LOT less, though it loads at half the rate or so of the 650:

1. RL550 press, with .45acp caliber kit - $379.95
2. Powder sensor - $39.95 (dunno if I’d bother)
3. Roller handle - $32.95
4. Strong mount - $39.95
5. Bullet tray - $35.95
6. Case feeder - $229.95 (again, dunno if I’d bother)

Totals out at about $530, or $760 with a case feeder. I never really thought there was a point to having a case feeder with a manual indexing press, but we're trying to compare like with like here; and to my mind, there's not much point to an auto indexing press without one.

Dillon's caliber conversions include the pieces you need to setup quick caliber changes. For RL550s, they run $40 or $50 depending on caliber; and some calibers use the same pieces as others. The 650s conversions are generally $40 more than the 550s. Spare tool heads are about $15 or $20 and spare powder dies are $9 to complete a quickchange setup (you can add an individual powder measure for each caliber for an extra $60, but it's not necessary). You may also need to change the case feeder plate depending on case size (there are five:small and large pistol, small and large rifle, and magnum rifle), for another $35.

It takes 10-20 minutes to change calibers on a Dillon, including re-adjusting the dies. If you have a full quickchange, with the powder measure set etc.. it takes a bit more than 5 minutes; mostly verifying settings.

Of course Dillon isn't the only press manufacturer out there.

A Hornady LnL AP with a case feeder runs $665, shell plates are $35, plus the tool head bushings (the LnL press uses a fixed tool head with changeable bushings)for $15, and case feeder plate for $35.

An RCBS pro 2000 runs $445, again without a caliber conversion at about $60 (shell plate, die plate, bushings and inserts); and there's no case feeder (I thought there was one available for it, but its not on their web site).

Although I love a lot of Lee products, I don’t think any of the Lee progressives are suitable for the kind of volume I want to do. Also, I’m not looking for a commercial press or any of the “unusual” brands.

Honestly, given my experience with Dillon, all the accessories for them, their support etc.. and the fact that they're 15 miles from my house, I’m not seeing any advantage to going with anybody else. I’m willing to be convinced, but I haven’t seen anything especially convincing.

The real question for me, is whether the extra $140 or $370, plus the more expensive caliber kits, are worth the extra 300-500 rounds per hour.

I’m thinking it is. I think the price difference would probably make itself up in a year or two.

Now as to whether a progressive reloading setup is worth it to a new reloader, well, my kit as it stands would be about $400. With an RL550, and no case feeder, it would be about $300 more. Add in the case feeder and it's more like $550 more. Step up to the 650 and its about $700 more.

So is it worth it?

Well, how much do you shoot?

In a good year, I shoot something like 25,000 rounds (I had a 150k round year once. That was fun, but it wasn’t my money). In a bad year, it’s more like 10-15,000. I don’t have $10,000 a year for ammo. As it is I probably spend $3-5k a year on shooting, not including new guns.

Although I’ve been shooting less often this past year or so; typical for me would be two range trips a month, and at least 500 rounds per range trip; half of that .45acp. And that’s not including what my wife shoots (usually another 100 or so per trip, sometimes 200).

As I said in my other post, even cheap whitebox stuff is up to $0.30 a round now. That’s at least 3 grand in just ammo, and may hit $4500 never mind other supplies, new guns etc… and that's at a REDUCED level of shooting.

As I broke down above, loading for maximum economy with plate bullets, I can get under $0.11 a round. Thats only 1/3 the cost of commercial ammunition. Even assuming I average out to $0.15 a round, that's half the cost.

So, reloading in general saves me $1500 to $2500 a year...

Or it would if I reloaded all my ammo, which I don't because it's honestly a hassle. Yes, it's something I enjoy, but it's time consuming, and there's a fair bit of effort involved; especially when you're doing production line loading for a couple thousand rounds a month.

Presuming I DID reload everything I shot, that would be 10-20 hours a month just cranking the lever, never mind load development, adjustments, etc... on top of all the other shooting related stuff, and all the other pursuits in my life.

On a progressive press, that time could be cut by 2/3, maybe 3/4. I could load up all the ammo for my range trips the night before, in an hour or two, and be done with it; leaving more time for the fun parts of reloading like load development, and of course for the rest of my life.

So, is getting those 10 or 15 hours a month back worth it?

To me, absolutely.

Is it worth $300 more, $550 more, $700 more?

Well, if I only value my time at $6 an hour, and only presume one year of using the press, that's 120 hours.. $720.

I dunno about you, but I value my time a lot higher than $6 an hour. I'd rather spend that time with my wife, doing more interesting and productive things.

(woof, 6300 words)

Oh I've got a little list, and they never would be missed

K, I'm a little irritated with SiteMeter

Sitemeter has the last visit recorded to my site at 12:02:04am this morning. That's a bit odd, considering I usually see something like 800 visitors by now, and I have a half dozen comments this morning from as recently as 45 minutes ago.

Apparently the JavaScript bug that SiteMeter puts onto the page isn't loading properly, because when you lode my pages they load everything but 1% and then hang on that last 1% until timeout.

Now, to figure out where the problem lies...

UPDATE: It appears that yesterday they migrated sitemeter to a new server cluster; which seems to be causing the problem. Now, when/what will the resolution be?

Monday, April 09, 2007

More proof that I need a progressive press

I couldn't sleep last night, so I sorted my brass from the last three range trips (the last two of which were last week -more on that to come, because the second trip was very interesting), and put it in the tumbler to run the rest of the night.

How MUCH brass was interesting, particularly how much .45acp.

Now, this is just what I bothered to pick up. Mostly it’s the brass from my 625, and I usually shoot about 4 times as much total as just in the 625.

...250 rounds, including 120 that was still in moon clips (thank god for the moonsetter and demooner). Plus another 180 that was from my last range trip of 2006 (in December).

Now remember, that’s just from the 625; multiply that by 4 and were talking 1,000 rounds.

So, since I last did the sorting, before three trips ago; I’ve fired about 1000 rounds of .45. (and about 300 rds of 9mm, 300rds of .380, 300 rounds of .38, 150rds of .357, 200 rds of .30-06, 200rds of 12ga, and 50rds of 20ga). And again, that’s just me, not including my wife and friends.

2500 rounds, since the first of the year. Unfortunately I’ve only made it to the range about once a month so far this year; I usually go twice a month.

Assuming I just maintain my current slow pace, I’ll be at about 10,000 total rounds this year. If I can manage to get back to twice a month, then I may break 15k rounds this year.

Even cheap whitebox stuff is up to $0.30 a round now. That’s at least 3 grand in just ammo, and may hit $4500 never mind other supplies, new guns etc…

If I can buy in the biggest bulk I can manage, get the best deals possible etc… and using brass I’ve already got, supplemented with once fired; I can probably get under $0.11 a round. Thats only 1/3 the commercial ammo cost (of course that means Ill just shoot more. It’s impossible to save money on loading and shooting ;-).

I REALLLY need a progressive press. Hell, I could pre-buy a ton of crap in bulk and make 3 months worth of .45 in two or three hours.

Alternative Ulster


I love the song, I love the band... and that's a hell of an idea for a video.

It's such an upbeat bopping punk tune, but read the damn lyrics:


ALTERNATIVE ULSTER
(Fingers/Ogilvie)

Nothin' for us in Belfast
The Pound's so old it's a pity
OK, there's the Trident in Bangor
Then walk back to the city
We ain't got nothin' but they don't really care
They don't even know you know
Just want our money
And we can take it or leave it
What we need is

(Chorus:)
An Alternative Ulster
Grab it and change it it's yours
Get an Alternative Ulster
Ignore the bores and their laws
Get an Alternative Ulster
Be an anti-security force
Alter your native Ulster
Alter your native land

Take a look where you're livin'
You got the Army on your street
And the RUC dog of repression
Is barking at your feet
Is this the kind of place you wanna live?
Is this where you wanna be?
Is this the only life we're gonna have?
What we need is

(Chorus)

They say they've got control of you
But that's not true you know
They say they're a part of you
And that's a lie you know
They say you will never be
Free free free

Get an Alternative Ulster, Alternative Ulster, Alternative Ulster


Let me tell you something; punk is about being pissed off, mostly because you've been pissed on. Well, not to many people are as pissed off as the Irish in the north; since not too many people have been pissed on as much as they have.

Dvorak violates my copyright in a most offensive way

Several people have sent me messages about this over the weekend:

From Dvorak.org:

Notice each dipshit is shooting the next guy in the foot!

For years, ATV-riding, gun-toting sport shooters have flouted gun laws in part of Idaho’s high desert by taking pot shots at ground squirrels and other animals. Now, officials say, they’re also setting their sights on National Guard tanks that train in the area.

The federal Bureau of Land Management is considering expanding the gun-restricted area by 41,000 acres to try to limit shootings at Idaho Army National Guard troops who report slugs bouncing off their tanks on a regular basis.

Their dad

“There’s a segment of the shooting community that will shoot at anything that moves,’’ said John Sullivan, the area’s manager.

“It’s like World War III on the weekends,’’ he said.

Ah, the price of freedom.

Initially I wasn't going to do anything about it, but when I re-read the thing I was a bit pissed. Plus, Gordon Greene has had his image abused enough.

Anyway I just sent this off to john@dvorak.org since they've disabled webmaster and postmaster.

Sirs,

I initially sent this to webmaster@dvorak.org and postmaster@dvorak.org; however your spam filter is set to reject messages to those addresses. It is an important administrative convention that these addresses receive mail; so that administrators of other sites may contact your site in the event of an incident or emergency.

The photographs used in this post:

http://www.dvorak.org/blog/?p=10782

Are copyrighted (specifically "Teaminfidel 1" is copyright Chris Byrne, 2005; and "gunnut" is copyright Gordon Greene, 2001), and used without permission. Additionally Teminfidel1 is hotlinked without permission (commonly known as bandwidth stealing).

Honestly, I have no problem with the use of the infidel picture in the appropriate context. Blogs by their very nature are referential, and I believe fair use covers the use of such images in appropriate context. I don't much care that the picture is used in an offensive way here in general; however the pictures used have nothing to do with the post in question.

Actually, specifically though, I am rather angry that it has been implied that I shot at national guardsmen. I am retired Air Force officer myself; and served my country honorably for 8 years. I am sure Mr. Greene, a serious long range competitive shooter, and collector of obscure high powered rifles; would be similarly offended by the use of his image.

If you would please remove the pictures in question, it would be appreciated.

Thank you

Chris Byrne
Given what seems to be their general attitude, and the fact that they don't even obey the most basic netiquette; I doubt I'll see a response.

Course if they don't take it down immediately on notice of copyright... and then theres the libelous aspect... Maybe I should sue John Dvorak, just for being an ass.

UPDATE: I take back all of my comments about lack of responsiveness, and being an ass. I just got a personal reply from John Dvorak, apologizing for using the picture, and removing the post.